Neighborhood Garage Sale

Yesterday was our annual neighborhood garage sale. I usually jump in my car and make a pass through the neighborhood, in the past I have gotten some good deals.

This year there was everything from a really clean 55 Chevy Sedan Delivery,

to a barely used Bocee Ball set.

A block from my house I found this brand new bike with a $20 post it note on it. I didn't really even look at it before pulling cash out of my pocket. After a quick conversation with the owner he told me he had been given they bike at work and had never ridden it.

After explaining I would be back to pick it up I started walking to the next house, thinking I would now need to find one for Tania as well. I had been looking for a his and hers set but nothing I had really pursued.

Next door there were two his and her Schwinns that I was not sure if they were for sale or if someone had ridden them there. I looked around a bit and then asked the home owner if she was selling them. At this point I was just curious since I had just bought a bike. She informed me they were for sale for $10 apiece.

Now I have three bikes...

I looked them up online last night and found the Polaris is currently available and sells for around $240.00. The Schwinns are about 8 years old and sold for just over $200.00 apiece. I think I will sell the Polaris on Craigslist (the Schwinn is a better bike) and use the money to buy some lights for the Schwinns.

There is trail head for a bike path about .5 miles from our house that I would like to start riding on.

Snowblower - Oil Leak

Two weeks ago I was "summerizing" my snow blower and noticed it had a fairly big oil puddle under it. It has always leaked a little bit since it was new, a few drops here and there but this was a puddle.

Looking at the motor it is mounted to a flanged steel plate which is attached to the main axle. It looked like the oil was coming from around the plate, which appeared to be the bottom of the sump or an oil pan.

Its item #14 in this picture.

The gaskets for this engine are not available separately, you have to buy them as a set for $52.00.

Last week I bought a hole punch set from Harbor Freight in anticipation of making a new gasket, and last Monday I started taking the engine out. It was of course the first thing they put in place when they built the snow blower so getting it out took a little work.

When I unbolted it from the engine plate I realized that was not the leak, it was leaking from the engine side plate. That wouldn't be any harder to make a gasket for, just more things to take apart.

My new Harbor Freight hole punches worked very well and I was able to make a gasket quickly. I did learn one lesson, punch the holes before you cut out the gasket. The material is brittle enough that it will split if the hole is very close to the edge.

Once I got the gasket made it only took a little over an hour to get it back together and running.

Pressure Washer

Tania bought me a AR Blue pressure washer for my birthday back in February.  I wanted a low volume pressure washer I could connect to my CR Spotless water de ionizer.  Utilizing it will allow me to use less de-ionized water when I rinse the car. The downside is connecting two water sources to it because demonized water is a solvent and left in the pump it will eat it up.  To make this work I needed a bypass for the de-ionizer.

Last year in anticipation of getting a pressure washer, I built a bypass out of PVC. When I connected it last week it literally exploded sending PVC shrapnel around the garage. Looking at it, I have no idea why it failed but the fragile nature of the PVC had me concerned to begin with.  I went to Lowe’s and looked at copper then quickly dismissed that idea due to the cost, so I started looking at PEX.  I was able to source everything necessary from Menards, including all the garden hose adapters.

Because the PEX is much more flexible than PVC or copper, I needed to build a bracket to attach the splitter valve to. I had some aluminum angle left over from a previous project that I highloked together.

Unfortunately I didn’t notice the feet on the valve were too wide for the aluminum.  I debated making a new support or adding a plate to the support. After looking at the valve again I realized I could re-drill the holes closer too each other.

After I re-drilled the holes I trimmed down the ears.

The bracket was easily attached through existing holes in the CR Spotless and the PEX went together rather quickly. I also purchased another section of Gladiator wall system. I had plenty of extra hooks to hang the pressure washer and more importantly the hose which allows me to store it in loose coils. Hopefully this will help with some of the memory these high pressure hoses have.

Now I can easily run normal water through the pressure washer to remove all the de-ionized water.

Steering Column

One of the few things I have never liked about the Corvette is the driving position. It seemed no matter how I adjusted the seat or the tilt column I could never find the right spot. Specifically I didn't like sitting so far away from the steering wheel, I have always liked it fairly close.

In most cars you can just move the seat closer and its problem solved. In the Corvette moving the seat closer puts my knees into the bolster and I am unable to use the clutch properly. This problem was very apparent when I went open tracking and felt like I was fighting the car instead of controlling the car. My arms extended straight to the wheel made it a very tiring experience along with making me drive much slower.

After that weekend I started researching options to move the steering wheel closer to the seat.

Option 1 was to buy a telescopic steering column ($350-$400).

Option 2 was to buy a custom made steering wheel with a deeper dish to the wheel ($1,500+).

Option 3 was to buy a quick release steering hub, after market steering wheel, 5 point harnesses to make up for no airbag and a track bar to mount them to ($2,000).

None of those options seemed reasonable at the time, so I did nothing.

A few weeks ago I was looking on Ebay for a trim piece and came across a column for $250.00, so I started searching to see if they had dropped in price. I ended up finding a column from a 2012 with 18k miles on it for $100.00 shipped. It was also a complete column with all the controls, clock spring and trim pieces installed.

After taking the disconnecting the battery the air bag and steering wheel took maybe 15 minutes to remove. Fairly simple stuff, I've had both off the car 3-4 times before. The column itself has one connector for all of the controls and one for the airbags. After disconnecting those, there was one cross bolt though the steering shaft and four bolts holding the column in place.

While the physical structure of the columns were completely different the mounting points and connectors were the same. The mounts are slotted so I was able to move the column towards the driver an additional 1/4" while installing it.

Once installed and after driving the telescopic motor fully extended the column moved the steering wheel 1.5" closer to the driver. Everything on the column worked properly except the telescopic motor, without memory seats in the car there is nothing to power or control the motor. I plan to rectify this with either a pair of relays or an H-Drive circuit, either way should be fairly easy to wire up.

In addition to replacing the column I took the drivers seat out while the steering wheel was removed. Its far from necessary but makes it that much easier to remove. This allowed me to easily access the drivers side seat belt. Over the last year or so it had become very slow to retract and many times would not retract without help. While I was looking for a replacement I came across a video on YouTube where the author claimed he had the fix for most all seat belts with this problem. He went on to explain that the oils from your skin and hands along from dirt the belt attracts would cause it to swell up and then become too large to retract properly. In the video he cleaned about 60% of a belt by soaking it in water mixed with detergent. I basically did the same thing but by removing it I was able to soak closer to 95% of the belt.

This picture shows the belt after soaking for about five hours. The water turned almost oily with a small amount of dirt in the bottom.

After reinstalling it along with the seat the belt retracted like it was a new assembly, I was actually quite suprised that it worked this well.